ER316 符合：YB/T5092 2H08Cr19Ni12Mo2Si
不銹鋼焊絲 相當：AWS A5.9 ER316
ISO 14343-B-SS316
In accordance with：YB/T5902 2H08Cr19Ni12Mo2Si
Be equivalent to：AWS A5.9ER316
ISO 14343-B-SS316
說明： ER316 焊絲主要成分是18Cr-12Ni-2Mo。配用SJ601不銹鋼堿性燒結焊劑，其焊縫金屬具有良好的力學性能和抗晶間腐蝕性能，焊縫抗裂性良好；具有不增C，且Cr、Ni燒損小等特點。因合金含量高，耐腐蝕性能優良。
用途： 長應用于石油化工、化肥、尿素生產或儲存設備，如06Cr17Ni12Mo2（SUS316）等材料的焊接。
Instructions: The ER 316 welding stick consists mainly of 18Cr-12Ni-2Mo.It coordinates with the stainless steel alkaline sintered flux SJ601 .It’s welding line metal has good mechanical properties and resistance ability to intergranular corrosion and crack. It would not increase Si or C and would burn little Cr and Ni. Due to a low content of carbon, it has excellent inoxidability.
Use: It’s usually used to weld materials in petrochemical industry and production and storge facilities of fertilizer or urea, such as 06Cr17Ni12Mo2 (SUS316)
焊絲化學成分（%）
|
項目 |
C |
Mn |
Si |
Cr |
Ni |
Mo |
P |
S |
Cu |
|
保證值 |
≤0.08 |
1.00~2.50 |
0.30~0.65 |
18.00~20.00 |
11.00~14.00 |
2.00~3.00 |
≤0.030 |
≤0.030 |
≤0.75 |
|
例值 |
0.048 |
1.75 |
0.45 |
19.63 |
12.52 |
2.50 |
0.011 |
0.010 |
0.26 |
|
焊絲直徑（mm） |
Φ0.8 |
Φ1.0 |
Φ1.2 |
Φ1.6 |
Φ2.0 |
Φ2.5 |
Φ3.2 |
|
焊接電流（A） |
70~150 |
100~200 |
140~220 |
50~100 |
100~200 |
200~300 |
300~400 |
注意事項：
1. 保護氣體：注意保護氣體的純度，混合氣配比推薦Ar+1~3%O2。TIG采用純Ar。
2. 氣體流量：20~25L/min。
3. 干伸長度：15~25mm。
4. 將焊接部位的銹層、濕氣、油污、灰塵等確實除凈。
5. 室外焊接時，當風速大于1.5m/s應采取適當的防風措施，以防發生氣孔。
6. 以上建議僅供參考，在具體造作中以現場情況為準。必要時先進行工藝評定再確定焊接方案。
Cautions:
1. Consumers should pay attention to the shielding gas.The recommended gas mixture ratio is Ar and 1~3%O2.The TIG should use pure Ar.
2. The gas flow rate is 20~25L/min.
3. The elongation length is 15~25mm.
4. The rust scale, moisture, oil stain and dust in the welding position should be definitely cleaned.
5. When welding outdoors with over 1.5m/s wind speed,appropriate wind proof measures should be taken,in case of air vent.
6. The suggestions above are for reference only.TheER316 符合：YB/T5092 2H08Cr19Ni12Mo2Si
不銹鋼焊絲 相當：AWS A5.9 ER316
ISO 14343-B-SS316
In accordance with：YB/T5902 2H08Cr19Ni12Mo2Si
Be equivalent to：AWS A5.9ER316
ISO 14343-B-SS316
說明： ER316 焊絲主要成分是18Cr-12Ni-2Mo。配用SJ601不銹鋼堿性燒結焊劑，其焊縫金屬具有良好的力學性能和抗晶間腐蝕性能，焊縫抗裂性良好；具有不增C，且Cr、Ni燒損小等特點。因合金含量高，耐腐蝕性能優良。
用途： 長應用于石油化工、化肥、尿素生產或儲存設備，如06Cr17Ni12Mo2（SUS316）等材料的焊接。
Instructions: The ER 316 welding stick consists mainly of 18Cr-12Ni-2Mo.It coordinates with the stainless steel alkaline sintered flux SJ601 .It’s welding line metal has good mechanical properties and resistance ability to intergranular corrosion and crack. It would not increase Si or C and would burn little Cr and Ni. Due to a low content of carbon, it has excellent inoxidability.
Use: It’s usually used to weld materials in petrochemical industry and production and storge facilities of fertilizer or urea, such as 06Cr17Ni12Mo2 (SUS316)
焊絲化學成分（%）
|
項目 |
C |
Mn |
Si |
Cr |
Ni |
Mo |
P |
S |
Cu |
|
保證值 |
≤0.08 |
1.00~2.50 |
0.30~0.65 |
18.00~20.00 |
11.00~14.00 |
2.00~3.00 |
≤0.030 |
≤0.030 |
≤0.75 |
|
例值 |
0.048 |
1.75 |
0.45 |
19.63 |
12.52 |
2.50 |
0.011 |
0.010 |
0.26 |
|
焊絲直徑（mm） |
Φ0.8 |
Φ1.0 |
Φ1.2 |
Φ1.6 |
Φ2.0 |
Φ2.5 |
Φ3.2 |
|
焊接電流（A） |
70~150 |
100~200 |
140~220 |
50~100 |
100~200 |
200~300 |
300~400 |
注意事項：
1. 保護氣體：注意保護氣體的純度，混合氣配比推薦Ar+1~3%O2。TIG采用純Ar。
2. 氣體流量：20~25L/min。
3. 干伸長度：15~25mm。
4. 將焊接部位的銹層、濕氣、油污、灰塵等確實除凈。
5. 室外焊接時，當風速大于1.5m/s應采取適當的防風措施，以防發生氣孔。
6. 以上建議僅供參考，在具體造作中以現場情況為準。必要時先進行工藝評定再確定焊接方案。
Cautions:
1. Consumers should pay attention to the shielding gas.The recommended gas mixture ratio is Ar and 1~3%O2.The TIG should use pure Ar.
2. The gas flow rate is 20~25L/min.
3. The elongation length is 15~25mm.
4. The rust scale, moisture, oil stain and dust in the welding position should be definitely cleaned.
5. When welding outdoors with over 1.5m/s wind speed,appropriate wind proof measures should be taken,in case of air vent.
6. The suggestions above are for reference only.The specific operation is subject to the actual situations.If necessary, consumers should evaluate the technical qualification before determining the welding scheme. specific operation is subject to the actual situations.If necessary, consumers should evaluate the technical qualification before determining the welding scheme.